Fantom Vacuum VPW49H User Manual download pdf (Page 6)

Assembling the Pressure Washer

OPERATING INSTRUCTIONS

Attaching High Pressure Hose to

Pressure Washer

Garden Hose Connection

2. Then attach the other end of the high

pressure hose to the high pressure

hose connector on the trigger gun.

(Fig. 9)

Fig. 9

3. Once the high pressure hose is

connected to the trigger gun, you can

attach any of the lances and

accessories that you desire. To

attach either of the lances or the

brush to the trigger gun, hold the

trigger gun in your left hand insert the

desired lance or the brush and push

it in all the way into the connector on

the trigger gun and turn it clockwise

60° until it locks in place. To remove

the attachment, push down on the

attachment and turn counter-

clockwise 60° and then pull out.

Make sure that the attachments are

securely locked in place before use.

(Fig. 10)

Fig. 2

Fig. 3 Fig. 4 Fig. 5

Fig. 6

Fig. 7

1 1/4”

SCREW

7/8”

SCREW

7/8”

SCREW

1. Carefully take all the parts out of the

packaging container and place

together on a flat, stable surface.

2. Insert the wheels onto the wheel

axle and push in the wheel lock to

lock the wheels in place. (Fig. 2)

3. Turn the pressure washer upside

down and slide the front support

onto the unit. (Fig 2)

4. Using the 1” long nickel plated

screw, secure the front support to

the unit.

5

Attaching The Wheels To The

Pressure Washer

Once all the desired attachments and

the high pressure hose are attached to

the pressure washer, you can connect

the garden hose to the unit.

1. Make sure that the water intake filter

is inside the water intake inlet.

(Fig. 11)

2. Attach the male adapter (supplied)

to the water intake connector on the

front side of the unit. (Fig. 11)

3. Attach the female hose coupling to

the garden hose. (Fig. 11)

4. Connect the female hose coupling

to the male adapter making sure

that it is tightly secured in place.

(Fig. 11)

Once the pressure washer is assembled,

you are ready to use the unit.

1. While facing the rear of the unit

attach the high pressure hose to the

high pressure output connector on

the back side of the unit. Twist on

tight to avoid leakage. (Fig. 8)

Fig. 8

Fig. 11

Water inlet

Water intake

filter

Garden hose

(not supplied)

Hose

connector

Garden hose

coupling

4. After all the connections have been

and

BEFORE you plug the pressure

washer into an electrical outlet, open

the water supply and press on the

trigger switch in order to remove any

air which may be in the hose or

pump. Continue to press on the

trigger switch until you get a constant

flow of water coming out of the trigger

gun. Allow water to flow for 30

seconds.

5. Once this is accomplished, stop

pressing the trigger switch. Engage

the safety lock on the trigger

6. Ensure that the "On/Off" switch, at

the side of the unit, is on the "Off"

position, then plug the unit into an

electrical outlet and turn the unit to

the "On" position.

7. Now you are ready to use the

pressure washer. Disengage the

safety lock and depress the trigger on

the trigger gun.

Attaching The Handle To The

Pressure Washer

1. Place the handle on the unit as

shown in Fig. 3.

2. Push the handle in at the bottom

until it is in position. See Fig. 4.

3. Let the handle slide down to its

resting place as shown in Fig 5 & 6.

4. To secure the handle to the unit,

screw 1 1/4” screw at the top hole

and the two (2) 7/8” screws on each

side of the handle. See Fig. 7.

Fig. 10

6

1 2 3 4 5 6

Comments to this Manuals

No comments